>> เช็คสต๊อคสินค้า <<

• Supply voltage: DC 12-24V
  
• Input Current: DC 0-5V
  
• Output voltage: 4-20mA
  
• Size: 55 x 25 x 13mm
• Zero and span can be adiusted (potentiometer adjustment). With the isolated nature of the non-optically isolated.

Package Included:

• 1 x Voltage to Current Transmitter Signal Module

 รับประกันสินค้า 15 วัน

>> เช็คสต๊อคสินค้า <<

รายละเอียดสินค้า

• Size 40mm * 25mm * 12mm
  
• Supply voltage: 7-30DC
  
• Input Current: 0 / 4-20mA
  
• Output voltage: 0-2.5v
  – 0-3.3v
  – 0-5.0v
  – 0-10.0v
  – 0-15.0v
  – 0-24.0v
  
• Temperature drift: + – 100ppm / c
  
• Ambient temperature: -10-60c
  
• Storage temperature: -20-85C
  
• Relative humidity: -20-85C
  
• Atmospheric pressure: 86-106KPA
  

Package Included:

• 1 x Current-to-Voltage Module

 รับประกันสินค้า 15 วัน

>> เช็คสต๊อคสินค้า <<

This signal generator DIY kit is professional product to generate sine/triangle/square wave. It's a DIY kit for you to weld and install.

Features:

• High resolution, can generate sine/triangle/square waveforms.
• Frequency range: 1Hz-1MHz.
• Adjustable frequency and amplitude.
• Frequency adjustment features coarse tuning and fine tuning.
• Wide power supply range, use 9-12V external power or 9V battery(NOT Included).
• All are through hole components, easy for installation.

Specifications:

• Voltage Supply: 9-12V DC Input
• Waveforms: Square, Sine & Triangle
• Impedance: 600 Ohm + 10%
• Frequency: 1Hz-1MHz

SINE WAVE

• Amplitude: 0-3V at 9V DC Input
• Distortion: Less than 1% (at 1KHz)
• Flatness: +0.05dB 1Hz – 100kHz

SQUARE WAVE

• Amplitude: 8V (no load) at 9V DC Input
• Rise Time: Less than 50ns (at 1KHz)
• Fall Time: Less than 30ns (at 1KHz)
• Symmetry: Less than 5% (at 1KHz)

TRIANGLE WAVE

• Amplitude: 0-3V at 9V DC Input
• Linearity: Less than 1% (up to 100KHz) 10mA
• Package Size: Approx. 12 * 8 * 2cm / 4.72 * 3.15 * 0.8in
• Package Weight: 69g / 2.46oz

Package List:

• 1 * Signal Generator DIY Kit
• 1 * User Manual(English)

ไม่มีรับประกันสินค้า

>> เช็คสต๊อคสินค้า <<

Description:

• Easy to connect wire and use, knob operation.
  
• In response to the output immediately after adjustment, no delay.
  
• With polarity protection, power reverse does not work, do not burn components.
  
• Power supply voltage: DC 9V~24V, Total power <1.5W.
  
• Output load impedance range between 0-350 ohms(DC 12V); 0-800 ohms(DC 24V).
  
• Can be used: signal sources, regulating valves, test instrumentation, light emitting diode test, the inverter output analog transmitter.
  

Specifications:

• Power Supply: DC 12V/24V
  
• Total Power: <1.5W
  
• Output: 4-20mA
  
• Output Load Impedance: 0-350 ohms(DC 12V); 0-800 ohms(DC 24V)
  
• Total Size:80*42*40mm (L*W*H)
  
• Hole Size:76*40mm (L*W)

Package includes:

• 1 x Signal Generator

รับประกันสินค้า 1 เดือน

>> เช็คสต๊อคสินค้า <<

ICL8038 Low-frequency Signal Source Generator Module Sine Square Triangle Waveform Generator Generator 01001-300KHz

The ICL8038 waveform generator is a monolithic integrated circuit capable of producing high accuracy sine, square, triangular, sawtooth and pulse waveforms with a minimum of external components. The frequency (or repetition rate) can be selected externally from 0.001Hz to more than 300kHz using either resistors or capacitors, and frequency modulation and sweeping can be accomplished with an external voltage.

Features:

• It's brand new, good quality & high performance.
• Module size:50*50mm
• Module working voltage:±5V-±12V DC
• Low Frequency Drift with Temperature : 50ppm/oC
• Low Distortion Sine Wave:011%
• Triangle Wave Output Linearity : 011%
• Wide Frequency Range : 01001Hz to 300kHz
• Duty Ratio Range : 2% to 98%
• Simultaneous outputs an arbitrary Sine, Square, and Triangle Wave
• Easy to Use

Package included:

• 1 x ICL8038 Low-frequency Signal Source Generator Module Sine Square Triangle Wave

รับประกันสินค้า 15 วัน

>> เช็คสต๊อคสินค้า <<

Description

• Main AVR DDS V2.0 signal generator features:
• Simple circuit ;
• Dedicated high speed (HS) signal output up to 8MHz;
• DDS signal with variable amplitude and offset;
• DDS signals: sine, square, saw, rev saw, triangle, ECG and noise.
• 2×16 LCD menu;
• Intuitive 5 button keypad.
• Frequency adjusting steps: 1, 10, 100, 1000, 10000Hz;
• Restoring last configuration after power up.

Package included :

• 1 x DDS Function Signal Generator Module Sine Square Sawtooth Triangle Wave

ไม่มีประกันสินค้า

>> เช็คสต๊อคสินค้า <<

specifics

• DIY Supplies:Electrical

Description

• The main output waveform : sine wave and square-wave, e wave, sawtooth wave
• Maximum output amplitude:± 10Vpp (no-load)
• Output impedance :50Ω±10%
• Dc bias: ± 10V (no-load)
• Display: LCD1602 The main output waveform : sine wave and square-wave, e wave, sawtooth wave
• Maximum output amplitude:± 10Vpp (no-load)
• Output impedance :50Ω±10%
• Dc bias: ± 10V (no-load)
• Display: LCD1602
• Output frequency range:
     – Sine wave: 1Hz-500KHz
     – Square-wave: 1 Hz – 20kHz (the valid range)
     – e wave :1 Hz – 20KHz (the valid range)
     – Sawtooth wave :1 Hz ~ 20kHz (the valid range)
• Resolution :1 Hz
• Power supply: DC 3.5-10V

Package included :

• 1pcs 1HZ-500KHz DDS Function Signal Generator Module Sine+e+Square Wave +case

รับประกันสินค้า 1 เดือน

>> เช็คสต๊อคสินค้า <<

Arbitrary waveform DDS signal generator from MHS-5200A series is a multi-functional signal generator with high precision and high performance. It adopts large scale of FPGA integrated circuits, high-speed MCU microprocessor and SMT in the inner circuit, which can greatly improve the anti-interference and lifetime of the instrument. The LCD display is divided into two lines: the top line shows the current frequency and the following line displays additional parameters or functions. This instrument is of great advantage in generating signal, scanning waveform, measuring parameters, etc. It's an ideal testing or measuring instrument for electronics engineer, electronic laboratory, teaching and researching.
  
Features:

• Can output arbitrary waveforms and conventional function waveforms(sine/triangle/square/sawtooth wave and TTL signal).
• All functions are digitally controlled, precise and stable.
• Dual-channel output, can work in sync, phase difference is adjustable.
• With linear sweep(Max. up to 999s) and logarithmic frequency sweep functions.
• Signal of both channels has built-in sophisticated -20dB attenuator in order to reach the minimum amplitude resolution 1mV.
• With 120% ~ + 120% DC bias function.
• 4 TTL output(phase difference is adjustable).
• Has a frequency measurement, period measurement, positive and negative pulse width measurement, duty cycle measurements and counting function.
• With USB interface, after the connection with PC, the PC can be used to control the instrument.

Specifications:

Package List:

• 1 * Signal Source Generator
• 1 * USB Cable
• 1 * CD
• 1 * TTL Expansion Board
• 2 * BNC Clips Cable  

รับประกันสินค้า 3 เดือน

>> เช็คสต๊อคสินค้า <<

JDS2900 digital control dual channel DDS function Arbitrary waveform signal generator, with a small size, easy to carry, good stability and other characteristics, the two channels are completely independent, all parameters can be achieved at the same time; can output function signal, pulse signal, Signals, digital signals and custom arbitrary waveform signals, and has a counter and measurement signal function; the use of large-scale FPGA integrated circuits, high-speed MCU microprocessors and high-precision oscillator as the basis of internal circuits, the signal more stable. SMT technology can greatly improve the anti-interference and life of the instrument; electronic engineers, electronic laboratories, research institutes and electronic enthusiasts worthy of the equipment.

Features:

1. Adopt 320*240 2.4″ TFT color LCD display, simultaneously display parameters of CH1 and CH2, Ability to reproduce patterns of custom waveform.
2. Using DDS direct digital synthesis technology to generate precise, stable and low distortion output signal.
3. Max. output frequency(sine wave) up to 15MHz/30MHz/40MHz/50MHz/60MHz(optional), 266MSa/s sampling rate and 14bits vertical resolution.
4. Completely independent dual channels output, synchronizing operation and adjustable phase difference.
5. Great improvement for square wave performance, square frequency range up to15MHzwith no distortion.
6. 60 groups of arbitrary wave storage function, memory depth of each group is2048*14bits.
7. High frequency accuracy and resolution: frequency accuracy up to 10^(-6) magnitude, total range frequency resolution is 0.01uHz.
8. High amplitude resolution: the minimum amplitude resolution can reach 1mV, amplitude range is 0Vpp~20Vpp.
9. Duty-cycle of each channel can be adjusted independently0.1%-99.9%, the adjusting resolution is 0.1%.
10. Pulse pulse width and pulse cycle time is precisely adjustable, adjust the range of 30nS-4000S
11. Scanning features: linear sweep and logarithmic sweep functions; 0.1s-999.9s sweep time; sorward, backward and roundtrip sweep directions.
12. With pulse trains burst output function, allow the unit output 1~1048575 arbitrary pulse trains.
13. Measurement functions: can measure signal frequency, cycle, positive/negative pulse width and duty cycle; 1Hz~100MHz frequency range.
14. -9.99V~9.99V DC offset range, offset resolution: 0.01V.
15. With digital signal output function, CMOS output range 0~10V.
16. Storage feature: can store 100 groups of parameters set by the user and extract at any time.
17. Counter function: with DC and AC coupling modes.
18. Arbitrary wave editing function: user can edit arbitrary wave on PC and then download to output from the instrument.
19. Communication function: the PC can be used to control the instrument.
20. With output short-circuit protection: all signal output can work 60s under load short-circuit condition.

Frequency Characteristic:

• Sine frequency range: 0~15MHz
  
• Square frequency range: 0~15MHz
  
• Triangle frequency range: 0~15MHz
  
• Pulse frequency range: 0~6MHz
  
• TTL digital frequency range: 0~6MHz
  
• Arbitrary wave frequency range: 0~6MHz
  
• Square rise time: ≤25nS
  
• Pulse width adjustment range: 150nS-4000S
  
• Mininum Frequency resolution: 0.01µHz(0.00000001Hz)
  
• Frequency accuracy: ±20ppm
  
• Frequency stability: ±1ppm/3h

• 1 x signal generator
• 1 x USB communication cable
• 1 x CD
• 1 x Power Adapter
• 2 x BNC Cable Clips 
• 1 x Dual BNC straight line

รับประกันสินค้า 3 เดือน

>> เช็คสต๊อคสินค้า <<

 
Features:

1. JDS6600 series Dual-channel Function Signal generator combines multiple functions in one, such as Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator, Sweep, Counter and Frequency Meter, etc. 
2. The instrument adopts the Direct Digital Synthesizer(DDS) technology and provides stable, precise, pure and low distortion signals. 
3. With output short-circuit protection: all signal output can work 60s under load short-circuit condition.
4. Use soft silicone keys instead of traditional patch keys, high sensitivity and convenient for operation.
5. It's a great testing or measuring instrument for electronics engineers, electronic laboratory, teaching and researching.

Specifications

• Model: JDS6600
• Plug: US/EU/UK/AU(optional)
• Sine frequency range: 0~60MHz
• Square frequency range: 0~25 MHz
• Triangle frequency range: 0~25 MHz
• Pulse frequency range: 0~6 MHz
• TTL digital frequency range: 0~6 MHz
• Arbitrary wave frequency range: 0~6 MHz
• Square rise time: ≤10nS
• Pulse width adjustment range:25nS – 4000S
• Frequency accuracy: ±20 ppm
• Frequency stability: ±1 ppm/3h

Waveform specifications:

• Waveform:  Sine, square, triangle, pulse (duty-cycle correction, pulse width and cycle time adjustable), arbitrary wave, CMOS, DC level, half-wave, full-wave, pos-ladder, neg-Ladder, noise, exponential rise, exponential fall, tone, cink pulse, lorentz pulse, and 60 kinds user-defined waveforms.
• Waveform vertical resolution: 14 bits
• Waveform sampling rate: 266 MSa/s
• Waveform length: 2048 points
• Sine – Harmonic suppression: ≥45dBc(Sine – Total harmonic distortion:   <0.8%(20 Hz~20 kHz,0dBm)
• Square and Pulse – Overshoot (Square): ≤5%
• Square and Pulse – Duty-cycle range(Pulse):   0.1 – 99.9%
• Ramp wave – Linearity: ≥98%(0.01 Hz~10 kHz)

Output specifications:

• Amplitude range:  Frequency<10MHz,0-20VPP; Frequency10 MHz, 0 – 10Vpp.
• Amplitude resolution:   1 mV
• Amplitude stability:   ±0.5%/5 h
• Amplitude flatness:  ±5%(10 MHz)

Waveform specifications:

• Output impedance:   50Ω±10%(typical)
• Protection:   Short circuit 60S will not be damaged
• DC Offset:
• Offset adjusting range: Output Amplitude>2V,-9.99V~9.99V;0.2VOffset resolution:   0.01 V

Phase specifications:

• Phase adjusting range: 0~359.9o
• Phase resolution: 0.1o

TTL/COMS Output:

• Low level:   High level:   1 – 10 V
• Level rise/fall time:   ≤20ns

External measurement functions:

• Frequency meter function – Frequency measurement range:   1 Hz~100 MHz
• Frequency meter function – Measurement accuracy: Gate time continuously adjusted between 0.01S~10s
• Counter function – Counting region: 0-4294967295
• Counter function – Coupled mode: 2 Coupling modes, DC and AC
• Counter function – Counting mode: Manual operation.
• Input signal voltage range: 2 – 20 Vpp
• Pulse width measurement: 0.01us (resolution), 20s (MAX measuring time)
• Period measurement:   0.01us (resolution), 20s (MAX measuring time)

General technical parameters:

• Display type: 2.4 inch TFT color LCD
• Storage and loading – Quantity: 100 groups
• Storage and loading – Location: 00 to 99(extract 00 place data at default boost state)
• Arbitrary wave – quantity: 1 to 60, totally 60 groups (default boost 15 groups)
• Interface mode: USB to serial interface
• Extension interface: There is serial interface of TTL level mode to be convenient for secondary development.
• Communication speed – Adopt standard:   115200 bps
• Communication protocol – Adopt command:   line mode, open protocol
• Power supply: DC 5 V±0.5 V
• Manufacturing process:   Surface-mount technology, large scale integrated circuit, high reliability, long service life
• The user can set ON or OFF by procedure
• Operating characteristics: Full button operation, knob continuous adjustment.

Sweep Functions:

• Sweep channel: CH1 or CH2
• Sweep type: Linear sweep, log sweep
• Sweep time: 0.1s~999.9s
• Setting range: Arbitrarily set between start point and stop points
• Sweep direction: Forward, backward and round trip

Package informations:

• Package Size: 240x210x95mm/9.36×8.19×3.71in
• Package weight: 990g/2.18lb
• General Box Package

Package included:

• 1 x Signal Source Generator
• 1 x CD
• 1 x Power Adapter(In:100~240V~50/60Hz,Out:5.0V-2.0A)
• 1 x USB Data Cable
• 1 x BNC-BNC Cable
• 2 x BNC-Clip Cable
• 1 x Instruction manual

รับประกันสินค้า 1 ปี

>> แจ้งความต้องการสินค้า <<

DG1000Z series function/arbitrary waveform generator is a multi-functional generator that combines many functions in one, including Function Generator, Arbitrary Waveform Generator, Noise Generator, Pulse Generator, Harmonics Generator, Analog/Digital Modulator and Counter.As a multi-functional, high performance and portable generator, it will be a new selection in education, R&D, production tests etc.

Features and Benefits

• DG1022Z 25 MHz Arbitrary Function Generator with second channel
• SiFi (Signal Fidelity) for 100% waveform replication
• 2Mpts or 8Mpts/CH(std.), 16Mpts/CH (opt.) arbitrary waveform length 
• Standard 2 full functional independent channels
• ±1ppm frequency stability, -125dBc/Hz phase noise, 200ps low jitter
• Built-in 8 orders harmonics generator
• Built-in 7 digits/s counter up to 200MHz
• 160 built-in pre-edited waveforms 
• Intuitive arbitrary waveform editing software
• Full modulation supported: AM, FM, PM, ASK, FSK, PSK and PWM

Advanced functions:

Large screen display , novel and beautiful appearance

Product Features:

• Standard 2 full functional channels

Standard dual full functional channels which are equivalent to two independent generators Copy, coupling and track is available to use between two channels. The phase of two channels can be adjusted accurately.

• Arbitrary waveform function with innovative SIFI technology

Innovative SiFi (Signal Fidelity) can generate arb waveform point-by-point, restore signal distortionless, precisely adjustable sample rate and low jitter (200ps).

• 160 built-in waveforms

160 built-in arbitrary waveforms, classified by Engine, Medical, AutoElec and Maths.

• Burst and Sweep function

• Multiple analog and digital modulations

DG1000Z supports AM,FM, PM, ASK, FSK, PSK and PWM modulations.

• Standard harmonic generator

DG1000Z can be used as a harmonic generator to output harmonic with specified order, amplitude and phase. It is usually used in the test of harmonic detector device or harmonic filter device.

• Waveform summing function

Superpose specified waveform onto basic waveform

• 7 digits/s full function frequency counter

Frequency resolution is 7 digits/second, frequency range is 1μHz ~ 200MHz. The measured value including: frequency, period, duty cycle and pulse width.

รับประกันสินค้า 1 ปี